Dense Phase vs Dilute Phase Pneumatic Conveying: Which One Do You Need?

Dense phase conveying pushes material through the pipe as slow, dense plugs using compressed air at higher pressure. Dilute phase conveying blows material along suspended in a fast, low-pressure air stream. Choose dense phase for abrasive, fragile or blended powders and for long distances. Choose dilute phase for free-flowing, non-abrasive materials over short to medium distances, where it costs less to buy.

The choice shapes everything else in the system: the air mover, the feeder, the pipe bore, the bends and the power bill. Getting it wrong means either broken product and worn bends, or paying for more equipment than the job needs. This guide sets the two side by side in plain terms, from what Scorpio BMH has learned commissioning 1,552+ dense phase and 1,156+ dilute phase systems since 1984.

Dense phase vs dilute phase at a glance

ParameterDense phaseDilute (lean) phase
How material movesSlow plugs or a moving bed, pushed by airSuspended in a fast air stream
Conveying velocityAbout 3–10 m/sAbout 20–30 m/s
Solids-to-air ratioHigh: 10 to over 100 kg of material per kg of airLow: under 10 kg/kg
Conveying pressureAbout 2–6 bar(g)Up to 1 bar(g)
Typical distanceUp to about 1,500 mUp to about 300 m
FeederPressure vessel (blow tank / powder pump)Rotary airlock valve
Air moverCompressor (for the higher pressure)Roots blower
Product breakageVery lowHigher; not for friable materials
Pipe and bend wearLowHigh with abrasive materials
Energy per tonneLower (less air)Higher
Upfront costHigherLower

How dense phase conveying works

Material drops into a pressure vessel. In Scorpio systems this is the Dense Flo Vessel. The vessel is sealed and pressurised, and compressed air pushes the charge down the pipeline as slugs or plugs at low speed. Because the material moves slowly and in bulk, very little of it touches the pipe wall at speed: bends last longer and particles arrive in the shape they left.

Scorpio’s twin-pulse air knife system is built for the lowest energy use per tonne, and low velocity is what lets dense phase systems run long distances with little wear.

See how Scorpio builds these systems: dense phase pneumatic conveying systems.

How dilute phase conveying works

A Roots blower supplies a high volume of air at low pressure. A rotary airlock valve meters material into the air stream, which carries the particles in suspension to the destination. There a cyclone or filter receiver separates the material from the air. The equipment is simpler and cheaper, and the system runs continuously at the push of a button.

The cost of that simplicity is speed. Particles hit the pipe walls and bends hard at 20–30 m/s, so abrasive materials wear the line and fragile ones break.

See how Scorpio builds these systems: dilute phase pneumatic conveying systems.

When to choose dense phase

  • Abrasive materials such as cement, fly ash, alumina, silica sand, lime and soda ash. Low velocity means little erosion of pipes and bends.
  • Fragile or friable materials where breakage creates fines, dust or off-spec product, for example carbon black pellets.
  • Blended materials, such as glass batch or detergent powders, that must not separate on the way.
  • Long distances or high capacities, where moving less air per tonne pays back the higher equipment cost.

When to choose dilute phase

  • Free-flowing, non-abrasive materials such as flour, sugar, grain and plastic pellets.
  • Short to medium runs inside one building or between nearby silos.
  • Several pick-up points to one destination, often as a vacuum system.
  • Tight budgets, where the material tolerates higher speed and the run is short.

Materials that can go either way

Some materials can be conveyed in either mode. The answer depends on three things: how much breakage the product can tolerate, how far it has to travel, and how many tonnes per hour you need. The more fragile the product and the longer the run, the stronger the case for dense phase. A material test settles it.

Four questions to answer before you choose

  1. What exactly is the material? Bulk density, particle size, moisture, abrasiveness, cohesiveness and whether the dust can explode. Bulk density alone can vary widely: fly ash ranges from about 700 to 1,400 kg/m³ depending on the source.
  2. How far, how high, and through how many bends? Each 90° bend adds roughly 7–10 m of equivalent horizontal pipe in pressure drop.
  3. How many tonnes per hour, and is the demand steady or in batches? A system sized for the average blocks at peak.
  4. What matters more: upfront cost or running cost? Dilute phase usually costs less to buy; dense phase usually costs less per tonne to run.

The most common mistake

The mistake Scorpio sees most often is choosing dilute phase for a material that cannot take the speed. The result is broken pellets, dust and worn bends within months. The fix is to start with the material, not the price, and to test it before sizing a single pipe. The full step-by-step method is in our pneumatic conveying system design guide, and an overview of both system types is on our pneumatic conveying and powder handling systems page.

Not sure which mode suits your material? Send Scorpio BMH your material, capacity and layout and an engineer will recommend dense or dilute phase.

Frequently asked questions

Is dense phase better than dilute phase?

Neither is better in general. Dense phase is better for abrasive, fragile or blended materials and long distances. Dilute phase is better value for free-flowing, non-abrasive materials over short to medium runs.

Which uses less energy, dense or dilute phase?

Dense phase usually uses less energy per tonne because it moves far less air for each kilogram of material. Dilute phase usually costs less to buy.

Can dilute phase convey abrasive materials?

It can, but at 20–30 m/s abrasive particles wear pipes and bends quickly. For cement, fly ash, alumina or silica sand, dense phase is the usual choice.

How far can each type convey material?

Dense phase systems typically convey up to about 1,500 m and dilute phase systems up to about 300 m. The real limit depends on the material, the capacity and the number of bends.

What conveying velocity does each type use?

Dense phase runs at about 3–10 m/s. Dilute phase runs at about 20–30 m/s, fast enough to keep particles suspended in the air.